• Home
  • Opal Walkover DMX Kit
Go back

Opal Walkover DMX Kit

Opal Walkover DMX Kit
E995DMXKIT: 
Opal Walkover DMX Kit: 24v IP67 colour changing, outdoor lighting system, part of the remote control Smart lighting range.
Print this page
£679.50 (exc vat) £815.40 (inc vat)
IN STOCK
E995DMXKIT helps you create an atmosphere in your garden by adjusting the brightness of the light and giving you access to a whole new colour spectrum. Whether you want all your garden lights to be a cool blue or just need some lights dimming down later in the evening, the DMX kit offers a complete garden light solution. E995DMXKIT consists of the necessary components to install a colour changing garden light system, controlled by the flush mount B30DMX touch pad/wall controller with colour wheel (supplied.)
The kit is designed to give you the essential items needed to install a basic outdoor DMX system and allows other components to be added to the kit at a later stage.The kit comprises of 4 x E995RGBF recessed LED light fittings, 1x B30DMX touch pad/wall controller, 1 x T3800 6 way IP68 junction box, 1x T2435PT 35w power supply, 1x T9802 IP 65 junction box and 2 x T9972 20mm cable glands
 
Colour/Finish:  RGB
IP Rating :  IP67
Input Voltage: 24v
Installation for lights:

Direct burial in the ground : prewired with rubber cable and 20mm IP68 gland for connection to mains supply via a separate underground joint kit (order T9969 separately.) Provide 300mm depth of shingle drainage below the uplight: do not use in waterlogged ground.
Using a single a RCD for large numbers of 240v fittings is not recommended due to the risk of nuisance tripping. We advise the use of separate RCD protection for each circuit and a maximum of 12 fittings per RCD. Where a garden lighting installation of more than 12 spike mount or recessed lights per circuit is proposed, we suggest the installation of 12v units with transformers, which results in a significantly higher fault tolerance and reliability in the total installation.                                        
Installation for wall switch:

The DMX wall switch requires power from either 12v or 24v DC. The switch fits on a standard 1 gang back box or drylining box. Install switch on an inside wall, typically inside a conservatory or dining room overlooking the garden.                                     

Related Products

Accessories

4 Core 3 Metre Extension Cable 4 Core 3 Metre Extension Cable
£18.00 (exc vat) £21.60 (inc vat)
View Details

Sorry we don't have any accessories for this product

Cancel/Close

Installation materials for this product

Please wait
3 Pole IP68 In-Line Cable Connector 'Y' Split

3 Pole IP68 In-Line Cable Connector 'Y' Split

£8.00 (exc vat) £9.60 (inc vat)
BUY NOW
Ground Burial 2 Core Low Voltage Cable - 25m - 1.5mm²

Ground Burial 2 Core Low Voltage Cable - 25m - 1.5mm²

£28.00 (exc vat) £33.60 (inc vat)
BUY NOW
3 Pole IP68 In-Line Cable Connector

3 Pole IP68 In-Line Cable Connector

£8.00 (exc vat) £9.60 (inc vat)
BUY NOW
Ground Burial 2 Core Low Voltage Cable - 50m - 1.5mm²

Ground Burial 2 Core Low Voltage Cable - 50m - 1.5mm²

£55.00 (exc vat) £66.00 (inc vat)
BUY NOW

This selection shows the most commonly used installation materials for this product: for additional options please visit the installation materials section to finalise your shopping basket

I'm finished choosing my options
Cancel/Close

Lamps suitable for this product

Please wait

This selection shows the most commonly used lamps for this product: for additional options please visit the lamps section to finalise your shopping basket

I'm finished choosing my options